rear axle

Discussion in 'General Discussions' started by deboer03150, Jan 30, 2011.

Page 4 of 5
  1. Jan 31, 2011 at 8:27 PM #31
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    well last i new he had the cover off and was letting it drain while he loaded some hogs so thats where it sits now
     
  2. Jan 31, 2011 at 11:46 PM #32
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    well we got the axle out it turns out the seal was ripped baring wasn't too bad. and for the axle i'm going to be getting a new one
     
  3. Jan 31, 2011 at 11:49 PM #33
    Darth Bama

    Darth Bama Administator Staff Member

    Posts:
    24,234
    Likes Received:
    154
    Joined:
    Nov 28, 2010
    Location:
    Georgia
    That's better then replacing the whole rear end.
     
  4. Jan 31, 2011 at 11:58 PM #34
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    but if i did that then i could have the 3.73 possy i want
     
  5. Feb 1, 2011 at 10:51 AM #35
    79bronco

    79bronco Junior Member

    Age:
    37
    Posts:
    14
    Likes Received:
    0
    Joined:
    Jan 27, 2011
    Location:
    West Virginia
    So i guess ur truck is 2wd?
     
  6. Feb 1, 2011 at 7:19 PM #36
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    no it 4 wd
     
  7. Feb 1, 2011 at 7:34 PM #37
    supercrewzn

    supercrewzn Full Access Member

    Posts:
    7,871
    Likes Received:
    0
    Joined:
    Dec 4, 2010
    Location:
    ...
    Did the axle show some wear? Post pics of where the bearing would be sitting.
     
  8. Feb 1, 2011 at 7:37 PM #38
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    yes it has some wear but the replacement bearing is offset some to put it in a different spot and i'll put pic up when it all done
     
  9. Feb 2, 2011 at 9:25 AM #39
    79bronco

    79bronco Junior Member

    Age:
    37
    Posts:
    14
    Likes Received:
    0
    Joined:
    Jan 27, 2011
    Location:
    West Virginia
    then ud have to change the gears in the front diff to match it
     
  10. Feb 2, 2011 at 10:58 PM #40
    deboer03150

    deboer03150 Banned

    Posts:
    1,669
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Archer, IA (Northwest, IA)
    well we just finished it and while i had it in the shop also changed the oil and fuel filter:peace:
     
Page 4 of 5

Share This Page