Quick Question

Discussion in 'General Discussions' started by Auburnfan400, Mar 23, 2011.

Page 2 of 4
  1. Mar 23, 2011 at 4:57 PM #11
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    how big block did you get?
     
  2. Mar 23, 2011 at 4:59 PM #12
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    4 inch. I bought Jarretts spindle lift
     
  3. Mar 23, 2011 at 5:20 PM #13
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    sweeet!
     
  4. Mar 23, 2011 at 5:47 PM #14
    Big'un

    Big'un BillyBadAss

    Posts:
    14,556
    Likes Received:
    4
    Joined:
    Nov 27, 2010
    Location:
    Dont Matter
    4wheelparts sucks ...... still waitin on them to call me back since last friday
     
  5. Mar 23, 2011 at 6:10 PM #15
    TxFx04

    TxFx04 FFS Frequent Traveler

    Age:
    32
    Posts:
    21,338
    Likes Received:
    25
    Joined:
    Jan 17, 2011
    Location:
    Conroe, Tx
    well you want a slanted block so you're pinion angle won't be all messed up. are you gonna put a leveling kit in? if not 3.5" in the front and 4" in the back is gonna be really raked
     
  6. Mar 23, 2011 at 6:14 PM #16
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    i do believe he already has a leveling kit.
     
  7. Mar 23, 2011 at 6:21 PM #17
    Big'un

    Big'un BillyBadAss

    Posts:
    14,556
    Likes Received:
    4
    Joined:
    Nov 27, 2010
    Location:
    Dont Matter
    yep he has a levelin kit
     
  8. Mar 23, 2011 at 6:29 PM #18
    TxFx04

    TxFx04 FFS Frequent Traveler

    Age:
    32
    Posts:
    21,338
    Likes Received:
    25
    Joined:
    Jan 17, 2011
    Location:
    Conroe, Tx
    so it'll just be a little bit raked
     
  9. Mar 23, 2011 at 6:51 PM #19
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    Yea i got the same 1.5" spacer you got, and...for a whole nother inch of lift just a few more dollars i went ahead and stepped up to the 4. I figure i'll swap that spacer for a larger set of coil springs later on so it'll be perfect then
     
  10. Mar 23, 2011 at 6:54 PM #20
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    Well i wanted to give em a shot since they hosted that meet and were so nice to some of yall. Sounds like only Ricky, then again he did spend a grand there too haha. But yea i emailed them and all they'd say is "Call ###-####" i can't remember the number lol. So...i went ahead and bout the block kit from em since it was cheaper there and free shipping but other than that their site really wasn't that impressive unless your wanting to rake out alot of dough on a truck
     
Page 2 of 4

Share This Page