Quick Question

Discussion in 'General Discussions' started by Auburnfan400, Mar 23, 2011.

Page 1 of 4
  1. Mar 23, 2011 at 4:22 PM #1
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    I'm bought a spindle lift and need to order some blocks for the rear so i hopped on 4wheelparts since everyone seems to vouch for them and under the block sets i need they have 3 options for the "inch size" for the "hole" and "pin". I then emailed their technical helpdesk and was told to call some number. Called, and nobody answered. So point is, does anybody know which size i need?

    The options are

    9/16 in. Hole 9/16 in. Pin

    11/16 in. Hole 5/8 in. Pin

    9/16 in. Hole 9/16 in. Pin
     
  2. Mar 23, 2011 at 4:23 PM #2
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    well the first one and last one are the same, and thier smaller. so i say go with them
     
  3. Mar 23, 2011 at 4:29 PM #3
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    O sorry, under the last one, it adds "flat block" under the specs
     
  4. Mar 23, 2011 at 4:35 PM #4
    yz85rider2002

    yz85rider2002 Lowered Life

    Posts:
    10,319
    Likes Received:
    40
    Joined:
    Nov 28, 2010
    Location:
    South Carolina
    Go with the 9/16th first one or just measure yours.
     
  5. Mar 23, 2011 at 4:40 PM #5
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    Good enough for me. I couldn't see how the differences would matter a ton but being i don't do this all the time, and learning as i go, i wanna make sure i get this all right
     
  6. Mar 23, 2011 at 4:48 PM #6
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    the one that isnt flat block changes your pinion angle. weve put blocks in backwards in a jeep before haha. never knew there was a difference till then
     
  7. Mar 23, 2011 at 4:48 PM #7
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    ok, ordered the first set
     
  8. Mar 23, 2011 at 4:49 PM #8
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    ahh, should i have ordered the last set then, with the flat block?
     
  9. Mar 23, 2011 at 4:50 PM #9
    Old_Skl_Raptr

    Old_Skl_Raptr GrandsonOfTheConfederacy

    Age:
    35
    Posts:
    10,433
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Auburn, AL
    na your good with those.
     
  10. Mar 23, 2011 at 4:54 PM #10
    Auburnfan400

    Auburnfan400 Longbed done right!

    Age:
    35
    Posts:
    2,316
    Likes Received:
    1
    Joined:
    Nov 28, 2010
    Location:
    Hartselle, Alabama
    Good deal, thanks guys
     
Page 1 of 4

Share This Page