MyFX4Project Build Thread!!!

Discussion in 'General Discussions' started by MyFX4Project, Sep 29, 2012.

  1. str8t six

    str8t six never enough

    Posts:
    2,702
    Likes Received:
    19
    Joined:
    Jan 16, 2011
    Location:
    Back in VA
    just put a heat exchanger in the opening :D
     
  2. MyFX4Project

    MyFX4Project TRUCKIT

    Posts:
    2,818
    Likes Received:
    30
    Joined:
    Aug 7, 2012
    Location:
    Kansas
    Just cleared the code and its been off for like 15 miles gonna see how long it takes to come back.

    Sent from my Galaxy S3
     
  3. MyFX4Project

    MyFX4Project TRUCKIT

    Posts:
    2,818
    Likes Received:
    30
    Joined:
    Aug 7, 2012
    Location:
    Kansas
    Huh?

    Sent from my Galaxy S3
     
  4. MyFX4Project

    MyFX4Project TRUCKIT

    Posts:
    2,818
    Likes Received:
    30
    Joined:
    Aug 7, 2012
    Location:
    Kansas
    Did my rear brakes yesterday. Ebrake wasn't engaging so I tore it apart and cleaned everything and hooked it back up. Well turns out it was frozen so the shoes weren't getting pushed out. Now I need all new hardware and new shoes. I said f it and just took the whole assembly off and threw on new rotors and pads lol ill get to it later... who needs an ebrake?

    You can see how crusty everything is lol most likely they have never been touched or replaced much like everything else on my truck...

    Sent from my Galaxy S3
     

    Attached Files:

  5. MyFX4Project

    MyFX4Project TRUCKIT

    Posts:
    2,818
    Likes Received:
    30
    Joined:
    Aug 7, 2012
    Location:
    Kansas
    Well got bored today so decided to get some stuff done. Been wanting to clean and paint my toolbox for a while so busted it out. Used two cans of rustoleum bed coating for inside and outside of the toolbox. Then cut a piece of carpet out to lay on the inside. I'm really pleased with the outcome. The last pic is a before pic.

    Sent from my Galaxy S3
     

    Attached Files:

  6. joh408

    joh408 Full Access Member

    Posts:
    2,811
    Likes Received:
    0
    Joined:
    Feb 21, 2011
    Location:
    Highlands Ranch, CO
    Looks good man. Any specific reason for the carpet?
     
  7. Pity7700

    Pity7700 oh umm...uhh?

    Age:
    36
    Posts:
    7,900
    Likes Received:
    286
    Joined:
    Nov 28, 2010
    Location:
    Flat rock Michigan
    looks good dude!
     
  8. MyFX4Project

    MyFX4Project TRUCKIT

    Posts:
    2,818
    Likes Received:
    30
    Joined:
    Aug 7, 2012
    Location:
    Kansas
    A lot of my shat in there gets dirty so I'm gonna see if the carpet will hold all of the dirt and stuff then I can just lift it up and shake it out rather than takin the toolbox off to wash it. Its also going to help stuff sliding around as much. Its doesn't get too dirty because I'm not on a jobsite or anything but it does carry tools lol

    Sent from my Galaxy S3
     
  9. BlackThundah

    BlackThundah Aka LilWhiteFiddy

    Posts:
    5,222
    Likes Received:
    5
    Joined:
    Jan 18, 2011
    Location:
    Georgia
    The tool box looks great man. :peace:
     
  10. ak_cowboy

    ak_cowboy Penguin Hunter

    Age:
    39
    Posts:
    14,843
    Likes Received:
    359
    Joined:
    Nov 28, 2010
    Location:
    Alaska
    Nice job :peace: How's the new intake working out?
     

Share This Page