Pity7700 Build thread, why not? pic heavy!

Discussion in 'General Discussions' started by Pity7700, Jan 28, 2012.

Page 107 of 118
  1. Nov 11, 2013 at 7:43 AM #1061
    01f1502wd

    01f1502wd going up? yes i am.

    Age:
    35
    Posts:
    8,378
    Likes Received:
    10
    Joined:
    Nov 28, 2010
    Location:
    T.E.X.A.S
    The only clunking I hear is my trans shifting, you sure its not in tge trans?
     
  2. Nov 11, 2013 at 9:45 AM #1062
    TFIDDLE

    TFIDDLE VEEEE TEn

    Posts:
    7,291
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    North Mississippi
    My green truck done that the whole time I had it. Never figured out the issue

    Sent from my SCH-L710 using Tapatalk 2
     
  3. Nov 11, 2013 at 9:50 AM #1063
    cowboy

    cowboy Sheriff

    Posts:
    9,623
    Likes Received:
    64
    Joined:
    Nov 30, 2010
    Location:
    Lebanon, ohio
    Check your motor mounts, transfer case, u joints on the front driveline, might as well check the back while your at it. Cross member for the transmission,
    both cv axles
     
  4. Nov 11, 2013 at 11:04 AM #1064
    Pity7700

    Pity7700 oh umm...uhh?

    Age:
    34
    Posts:
    7,900
    Likes Received:
    286
    Joined:
    Nov 28, 2010
    Location:
    Flat rock Michigan
    I doubt its the trans. it doesn't clunk when I put it into reverse, in fact, if I let it roll in reverse I have no noise until I touch the pedal. even if I hit the pedal softly there isn't any noise. something is moving.

    transmission cross member was replaced a few months ago as well as the trans support on top of the cross member.
     
  5. Nov 11, 2013 at 11:20 AM #1065
    cowboy

    cowboy Sheriff

    Posts:
    9,623
    Likes Received:
    64
    Joined:
    Nov 30, 2010
    Location:
    Lebanon, ohio
    is that when the noise started?
     
  6. Nov 11, 2013 at 11:39 AM #1066
    Pity7700

    Pity7700 oh umm...uhh?

    Age:
    34
    Posts:
    7,900
    Likes Received:
    286
    Joined:
    Nov 28, 2010
    Location:
    Flat rock Michigan
    no the noise is fairly new.

    the reason I replaced the trans support was because the original on was cracked and I had a clunk sometimes in drive, the trans would shift. replaced the parts and problem solved. now that I think about it the sound seems similar. I did check the mount to see if it was tight and everything is good.
     
  7. Nov 11, 2013 at 11:40 AM #1067
    01f1502wd

    01f1502wd going up? yes i am.

    Age:
    35
    Posts:
    8,378
    Likes Received:
    10
    Joined:
    Nov 28, 2010
    Location:
    T.E.X.A.S
    which pedal are you touching? gas or brake?
     
  8. Nov 11, 2013 at 1:15 PM #1068
    Pity7700

    Pity7700 oh umm...uhh?

    Age:
    34
    Posts:
    7,900
    Likes Received:
    286
    Joined:
    Nov 28, 2010
    Location:
    Flat rock Michigan
    gas lol.
     
  9. Nov 11, 2013 at 1:21 PM #1069
    01f1502wd

    01f1502wd going up? yes i am.

    Age:
    35
    Posts:
    8,378
    Likes Received:
    10
    Joined:
    Nov 28, 2010
    Location:
    T.E.X.A.S
    ok just wanted to make sure :whistle:
     
  10. Nov 11, 2013 at 6:36 PM #1070
    Roush PSD Interceptor

    Roush PSD Interceptor 7.3L Straight Piped Diesel

    Age:
    58
    Posts:
    9,862
    Likes Received:
    576
    Joined:
    Nov 28, 2010
    Location:
    Ringgold, Georgia
    Gas pedal and fairly new noise.
    One would assume drive line issue.
    Seems like the last repair was front
    brakes correct?
     
Page 107 of 118

Share This Page