rough country lift

Discussion in 'Lifted' started by ranger, Jan 15, 2011.

Page 5 of 5
  1. Jan 18, 2011 at 10:05 PM #41
    TFIDDLE

    TFIDDLE VEEEE TEn

    Posts:
    7,291
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    North Mississippi
    dang that sucks
     
  2. Jan 18, 2011 at 10:06 PM #42
    Big'un

    Big'un BillyBadAss

    Posts:
    14,556
    Likes Received:
    4
    Joined:
    Nov 27, 2010
    Location:
    Dont Matter
    when mine blowed i bought a whole rearend out of a truck and droped mine and bolted the new one up
     
  3. Jan 18, 2011 at 10:20 PM #43
    TFIDDLE

    TFIDDLE VEEEE TEn

    Posts:
    7,291
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    North Mississippi
    yeah that would be prolly the cheapest route
     
  4. Jan 18, 2011 at 10:23 PM #44
    Big'un

    Big'un BillyBadAss

    Posts:
    14,556
    Likes Received:
    4
    Joined:
    Nov 27, 2010
    Location:
    Dont Matter
    costed me $800 and it was a pita to find one for a 97-03 f150 after i got it i found out i coulda got one out of a 87-96 also and just put my axles in it :facepalm:
     
  5. Jan 18, 2011 at 10:25 PM #45
    TFIDDLE

    TFIDDLE VEEEE TEn

    Posts:
    7,291
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    North Mississippi
    wow lol hahaha
     
  6. Jan 18, 2011 at 10:34 PM #46
    swamphunter

    swamphunter Full Access Member

    Posts:
    409
    Likes Received:
    0
    Joined:
    Nov 30, 2010
    Location:
    greeneville tn
    Mine came out of a mustang 100$ been holding up for 3 years now
     
  7. Jan 18, 2011 at 10:37 PM #47
    Big'un

    Big'un BillyBadAss

    Posts:
    14,556
    Likes Received:
    4
    Joined:
    Nov 27, 2010
    Location:
    Dont Matter
    bolted right up?
     
  8. Jan 18, 2011 at 10:39 PM #48
    swamphunter

    swamphunter Full Access Member

    Posts:
    409
    Likes Received:
    0
    Joined:
    Nov 30, 2010
    Location:
    greeneville tn
    Sure did
     
  9. Jan 18, 2011 at 10:48 PM #49
    ranger

    ranger Full Access Member

    Age:
    33
    Posts:
    219
    Likes Received:
    0
    Joined:
    Dec 16, 2010
    Location:
    Fond du Lac
    the gears in the carrier are shears off the ring and pinion are fine hes sending me pics shortly then ill post them up
     
  10. Jan 19, 2011 at 3:01 PM #50
    A7X

    A7X Full Access Member

    Posts:
    526
    Likes Received:
    0
    Joined:
    Nov 28, 2010
    Location:
    Mass
    No need to pull the front drive shaft... Unless you think yer gonna put it in 4x by accident... I installed 4.56s in the rear of my truck, just haven't got around to doin the front yet... and my front driveshaft is still in :waytogo:
     
Page 5 of 5

Share This Page